Monday, February 15, 2010

Pick-up Pleats

http://www.disboards.com/showthread.php?p=3536

I had asked on the Dis if anyone could help me figure out how to do these little pick up pleats. I was answered by FairyGoodmother:

Teresa, I think you're on the right track with the Precious Dress, and of course, Carla's sash. As for the "pick-ups" in the skirt, figure that you'll "pinch" about 1.5" per pickup, so however many rows of pickups you want, multiply that by 1.5 to figure your length. Place your pickups kinda in a pattern, like this:
.....X..........X

X..........X..........X

.....X..........X

As long as you have the same measurement between them, you'll be fine. Does that make sense?

The pickups are just that...you pick up the fabric, pinch it, then hand stitch it to hold in place. Oftentimes they're then covered up with roses, buttons, jewels.


I then asked her if the pleats should be made on the inside of the dress:

no - you pinch it on the outside and stitch it.

You actually COULD do it from the inside but the look is a bit different.
Play with it; see what look you prefer.

Unfortunately, I didn't get a chance to try this out on the dress I was making. I plan on trying it someday though! If you've tried it, send me a picture and I'll add it to this post.

Shopping Cart Cover by Adi12982

This was first posted on the Dis by Adi12982
Click on the picture to see the whole thing

What you need:

- Two different fabrics each 1 1/3 yards each (or a total of 2 and 2/3 yards if you want to use the same fabric on both sides)
- 1 1/3 yards of batting (the thicker the fluffier, not necessary, but nice)
- 1" wide elastic, 1 3/4 yards of it
- 1 package of matching double folded bias tape

OPTIONAL - if you want to have your own straps, instead of using the ones on the shopping cart - then:
- 1 yard of seat belt strapping
- 1 plastic locking seat belt connector


Instructions:

- lay your two pieces of fabric, right sides together and the batting and pin.
- stitch around the entire outer edge of the fabric (not the leg/belt holes - just the 4 outside edges of the cover).
I try to use only about a 1/4 - 1/2" seam around the outer edge so that you aren't taking up too much of the fabric. Stitch a solid
seam all the way around the outer edge of the cover and stop stitching about 6" before the starting point so that you end up
with a hole that you will use to turn the cover right side out.
- Turn the cover right side out.Top stitch around the VERY outer edge of the cover leaving the same 6" "hole" the way around to give the cover some added strength and a neat appearance.
- Now, you will stitch another seam around the outer edge, but not on the very edge, this seam will be 2" in from the outer edge of the cover. This seam will be a casing for the elastic around the outer edge. Make this seam 2" in from the outer edge all the way around the cover. You do not need to account for the "hole". (Now, when you look at your fabric, you will see one seam going all the way around the very outer edge, with an 8” section where you left an opening. Then, you will see another seam 2” further in from the first seam. This seam goes all the way around, without an opening. It starts and stops at the same place, without any gap.
7. At this point, you will want to finish your leg and seat belt holes. You can use the seam tape, which makes a nice, clean
appearance or you can use a serger or even a tight zig zag stitch close to the edge of the fabric. Whatever you chose to use is
up to you and depends on the look you want. What I do is mark with a fabric marker where the leg and seat belt holes should go, and then do an initial stitching around where I will be cutting, then I cut just inside - this helps keep it all together a little easier than just pinning (which I used to do).
- after cutting out the holes I then attach the bias tape around the leg hole cuts I made and the ones for the seat belt.
8. Now is time for the elastic. It is the hardest to do using a safety pin (your hands will get tired and it will take a while, but it can be done). What I have been using is one of those cheap curtain rods - I take the plastic cap of the end and push the elastic in a bit and then recap, and push through. If you have real tools for it, have at it. .. just get it through

Whichever way you use, once you have the elastic through
the casing and have both ends of the elastic back at the 8“opening, you will need to stitch the two ends of the elastic together
tightly so that it doesn't come apart. Once that’s done, stitch the 8" hole closed at the top/finish the edge top stitching.

9. Lastly, you need to make the seat belt, if you are making one. Split the seat belt material in half and attach at either side. I've never done this, but have seen that some do.

Double Cart Cover Alternate Instructions: To make the double cart cover, you will do everything exactly as stated in the original pattern, except you will need to make 4 leg holes instead of two and you'll need to make 4 seat belt holes instead of 2. You will need to purchase 2 yards of seat belt strapping, 2 locking clips for the seat belts and extra binding, since one package, most likely, will not cover all 4 leg holes and all 4 seat belt holes. To add the leg holes, you will need to cut one additional leg hole on either side of the original 2 leg holes. Space them 2" apart from the original holes, just as the two original holes are spaced 2" apart. So, you will end up with 9.5" of fabric left from the edge of the outer holes to the edge of the fabric, instead of the 16.5" which is shown in the original pattern. To add the seat belt holes, you will just look at the leg holes as two sets and put one hole above the outer edge of the leg holes of each set. (see the original iagram for placement above the set of leg holes and do this with each of the two sets).

Locking Serger Threads by TinkerbelleMom

Originally posted by TinkerbelleMom on the Dis.

Step one...slide hook under stitches.
______________
Step 2...grab the tail with whatever hook you're using.
_____________________________________________


Step 3...pull tail under stitches and trim as needed.

Saturday, February 13, 2010

New Background

Seriously, how cute is this background?? I found it at Shabby Blogs
I saw it and loved it, then I saw that it was called "Lydia's Apron" so I knew it was the one for me! LOL!

Thursday, February 11, 2010

A few things

I have a few things I'm going to need to put on here in the next few days. I got lazy and only put them in the bookmarks. I'll try to get them added here when I have a minute!